300-410 Exam Dumps Pass with Updated Jul-2023 Tests Dumps
300-410 exam questions for practice in 2023 Updated 530 Questions
The Cisco 300-410 exam is part of the Cisco Certified Specialist - Enterprise Advanced Infrastructure Implementation certification, which is designed for IT professionals who want to validate their skills in implementing advanced routing technologies and services in enterprise networks. The exam covers a wide range of topics related to enterprise routing and services, including advanced routing protocols, quality of service (QoS), virtual private networks (VPNs), and network automation.
NEW QUESTION # 165
Refer to Exhibit.
The network administrator configured the branch router for IPv6 on the E0/0 interface. The neighboring router is fully configured to meet requirements, but the neighbor relationship is not coming up. Which action fixes the problem on the branch router to bring the IPv6 neighbors up?
- A. Disable OSPF for IPv4 using the no ospfv3 4 area 0 ipv4 command under the E0/0 interface
- B. Enable the IPv4 address family under the router ospfv3 4 process by using the address-family ipv4 unicast command
- C. Enable the IPv4 address family under the E0/0 interface by using the address-family ipv4 unicast command
- D. Disable IPv6 on the E0/0 interface using the no ipv6 enable command
Answer: B
Explanation:
Once again, Cisco changed the IOS configuration commands required for OSPFv3 configuration. The new OSPFv3 configuration uses the "ospfv3" keyword instead of the earlier "ipv6 router ospf" routing process command and "ipv6 ospf" interface commands.
The Open Shortest Path First version 3 (OSPFv3) address families feature enables both IPv4 and IPv6 unicast traffic to be supported. With this feature, users may have two processes per interface, but only one process per address family (AF).
NEW QUESTION # 166
Refer to the exhibit.
An engineer configures SW101 to send OSPFv3 interfaces state change messages to the server. However, only some OSPFv3 errors are being recorded. which organization resolves the ..?
- A. snmp-server-enable traps ospfv3 state-change restart-status-change
- B. snmp-server-enable traps ospfv3 state-change if-state-change neighbor-state-change
- C. snmp-server-enable traps ospfv3 state-change neighbor-state-change.
- D. snmp-server enable traps ospfv3 state-change if-state-change
Answer: B
NEW QUESTION # 167
Refer to the exhibit.
A network is under a cyberattack. A network engineer connected to R1 by SSH and enabled the terminal monitor via SSH session to find the source and destination of the attack. The session was flooded with messages, which made it impossible for the engineer to troubleshoot the issue. Which command resolves this issue on R1?
- A. #terminal no monitor
- B. no terminal monitor
- C. (config)#terminal no monitor
- D. (config)#no terminal monitor
Answer: A
NEW QUESTION # 168
Refer to the exhibit. ISP 1 and ISP 2 directly connect to the Internet. A customer is tracking both ISP links to achieve redundancy and cannot see the Cisco IOS IP SLA tracking output on the router console.
Which command is missing from the IP SLA configuration?
- A. Start-time 00:00
- B. Start-time 0
- C. Start-time immediately
- D. Start-time now
Answer: D
Explanation:
Section: Infrastructure Services
Explanation
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipsla/configuration/15-mt/sla-15-mt-book/ sla_icmp_echo.html
NEW QUESTION # 169
Refer to the exhibit.
Which two commands provide the administrator with the information needed to resolve the issue? (Choose two.)
- A. showsnmpv3 user
- B. snmp user
- C. debug snmp packet
- D. debug snmpv3 engine-id
- E. debug snmp engine-id
Answer: A,B
NEW QUESTION # 170
Refer to the exhibit.
Which interface configuration must be configured on the spoke A router to enable a dynamic DMVPN tunnel with the spoke B router?
- A. Option B
- B. Option A
- C. Option D
- D. Option C
Answer: A
Explanation:
Explanation
The command ip nhrp map multicast dynamic should be only used on Hub router, not spoke. If we are running dynamic routing protocols based on multicast (like RIP, OSPF, EIGRP ...) we have to add the command ip nhrp map multicast dynamic in Hub to replicate all multicast traffic to all dynamic entries in the NHRP table (multicast will be proceeded as unicast traffic) - The tunnel source FastEthernet0/0 is equivalent to tunnel source 172.17.0.2, which is the NBMA address of Spoke A.
NEW QUESTION # 171 
Refer to the exhibit. A network administrator redistributed the default static route into OSPF toward all internal routers to reach to Internet. Which set of commands restores reachability to the Internet by internal routers?
- A. router ospf 1
redistribute static subnets - B. router ospf 1
network 0.0.0.0 0.0.0.0 area 0 - C. router ospf 1
default-information originate - D. router ospf 1
redistribute connected 0.0.0.0
Answer: C
NEW QUESTION # 172
Refer to the exhibit.
While monitoring VTY access to a router, an engineer notices that the router does not have any filter and anyone can access the router with username and password even though an ACL is configured.
Which command resolves this issue?
- A. access-class INTERNET in
- B. ipv6 access-class INTERNET in
- C. ipv6 traffic-filter INTERNET in
- D. ip access-group INTERNET in
Answer: B
NEW QUESTION # 173 
Refer to the exhibit. A network administrator configured an IPv6 access list to allow TCP return traffic only, but it is not working as expected. Which changes resolve this issue?
- A. ipv6 access-list inbound
permit tcp any any syn
deny ipv6 any any log
!
interface gi0/0
ipv6 traffic-filter inbound out - B. ipv6 access-list inbound
permit tcp any any established
deny ipv6 any any log
!
interface gi0/0
ipv6 traffic-filter inbound out - C. ipv6 access-list inbound
permit tcp any any established
deny ipv6 any any log
!
interface gi0/0
ipv6 traffic-filter inbound in - D. ipv6 access-list inbound
permit tcp any any syn
deny ipv6 any any log
!
interface gi0/0
ipv6 traffic-filter inbound in
Answer: C
NEW QUESTION # 174
Exhibit:
NTP is configured across the network infrastructure and Cisco DNA Center. An NTP issue was reported on the Cisco DNA Center at 17:15. Which action resolves the issue?
- A. Check and configure NTP on the WLC and synchronize with Cisco DNA Center
- B. Reset the NTP server to resolve any synchronization issues for all devices
- C. Check and resolve reachability between the WLC and the NTP server
- D. Check and resolve reachability between Cisco DNA Center and the NTP server
Answer: A
Explanation:
Excessive time lag between Cisco DNA Center and device: The time difference between Cisco DNA Center and the device IP Address has drifted too far apart. CiscoDNA Center cannot process the device data accurately if the time difference is more than 3 minutes.
NEW QUESTION # 175
Refer to the exhibit. An engineer must establish multipoint GRE tunnels between hub router R6 and branch routers R1, R2, and R3. Which configuration accomplishes this task on R1?
A)
B)
C)
D)
- A. Option A
- B. Option B
- C. Option C
- D. Option D
Answer: D
NEW QUESTION # 176
Refer to the exhibit.
An IP SLA is configured to use the backup default route when the primary is down, but it is not working as desired. Which command fixes the issue?
- A. R1(config)#ip sla track 1
- B. R1(config)# ip route 0.0.0.0.0.0.0.0.2.2.2.2 10 track 1
- C. R1(config)# ip route 0.0.0.0.0.0.0.0.2.2.2.2
- D. R1(config)# ip route 0.0.0.0.0.0.0.0.1.1.1.1 track 1
Answer: D
Explanation:
Reference:
Note: By default Static Router AD value-1 hence ip route 0.0.0.0. 0.0.0.0. 1.1.1.1 track 1 means AD-1 which must be less than of back up route AD.
Define the backup route to use when the tracked object is unavailable. !--- The administrative distance of the backup route must be greater than !--- the administrative distance of the tracked route. !--- If the primary gateway is unreachable, that route is removed !--- and the backup route is installed in the routing table !--- instead of the tracked route.
https://www.cisco.com/c/en/us/support/docs/ip/ip-routing/200785-ISP-Failover-with-default-routes-using-I.html
https://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-next-generation-firewalls/118962-configure-asa-00.html
NEW QUESTION # 177
Refer to the exhibit.
TCP traffic should be reaching host 10.10.10.10/24 via R2. Which action resolves the issue?
- A. Add a permit 20 statement in the route map to allow TCP traffic
- B. TCP traffic will reach the destination via R2 without any changes
- C. Set IP next-hop to 10.10.12.2 under the route-map permit 10 to allow TCP traffic.
- D. Allow TCP in the access list with no changes to the route map
Answer: D
NEW QUESTION # 178
Refer to the exhibit.
An engineer is trying to redistribute OSPF to BGP, but not all of the routes are redistributed. What is the reason for this issue?
- A. By default, only internal OSPF routes are redistributed into BGP
- B. By default, only internal routes and external type 1 routes are redistributed into BGP
- C. Only classful networks are redistributed from OSPF to BGP
- D. BGP convergence is slow, so the route will eventually be present in the BGP table
Answer: A
Explanation:
If you configure the redistribution of OSPF into BGP without keywords, only OSPF intra-area and inter-area routes are redistributed into BGP, by default.
You can redistribute both internal and external (type-1 & type-2) OSPF routes via this command: -Router(config-router)#redistribute ospf 1 match internal external 1 external 2
NEW QUESTION # 179
Drag and Drop the IPv6 First-Hop Security features from the left onto the definitions on the right.
Answer:
Explanation:
NEW QUESTION # 180
Refer to the exhibit.
Refer to the exhibit. An engineer implemented an access list on R1 to allow anyone to Telnet except R2 Loopback0 to R1 Loopback4 How must sequence 20 be replaced on the R1 access list to resolve the issue?
- A. sequence 20 deny tcp host 1001:ABC:2011:7::1 host 400A:0:400C::1 eq telnet
- B. sequence 20 permit tcp host 400A:0:400C::1 host 1001ABC:2011:7::1 eq telnet
- C. sequence 20 permit tcp host 1001 ABC:2011:7:: 1 host 400A:0:400C::1 eq telnet
- D. sequence 20 deny tcp host 400A:0:400C::1 host 1001 :ABC:2011:7::1 eq telnet
Answer: A
NEW QUESTION # 181
Refer to the exhibit.
Refer to the exhibit. An engineer has successfully set up a floating static route from the BRANCH router to the HQ network using HQ_R1 as the primary default gateway When the g0/0 goes down on HQ_R1, the branch network cannot reach the HQ network 192.168.20.0/24. Which set of configurations resolves the issue?
- A. BRANCH(config)# ip sla 1
BRANCH(config-ip-sla)# icmp-echo 192.168.100.2 - B. BRANCH(config)# Ip sla 1
BRANCH(config-ip-sta)# Icmp-echo 192.168.100.1 - C. HQ_R3(config)# ip sla responder
HQ_R3(config)# ip sla responder icmp-echo 172.16.35.1 - D. HQ R3(config)# Ip sla responder
HQ R3(config)# Ip sla responder Icmp-echo 172.16.35.5
Answer: B
NEW QUESTION # 182
Drag and drop the SNMP attributes in Cisco IOS devices from the left onto the correct SNMPv2c or SNMPV3 categories on the right.
Answer:
Explanation:
NEW QUESTION # 183
Refer to the exhibit. What does the imp-null tag represent in the MPLS VPN cloud?
- A. Include the EXP bit
- B. Exclude the EXP bit
- C. Impose the label
- D. Pop the label
Answer: D
Explanation:
Section: VPN Technologies
NEW QUESTION # 184
Refer to the exhibit.
Which statement about R1 is true?
- A. R1 adds one to the metric for RIP learned routes before redistributing to OSPF.
- B. RIP routes are redistributed to OSPF without any changes.
- C. OSPF redistributes RIP routes only if they have a tag of one.
- D. RIP learned routes are distributed to OSPF with a tag value of one.
Answer: D
NEW QUESTION # 185
Refer to the exhibit.
Refer to the exhibit. An engineer configured two ASBRs, 10.4.17.6 and 10.4.15.5, in an OSPF network to redistribute identical routes from BGR However, only prefixes from 10.4.17.6 are installed into the routing table on R1. Which action must the engineer take to achieve load sharing for the BGP-originated prefixes?
- A. The ASBRs are advertising the redistributed prefixes with the iBGP metric and must be modified to Type 1 on ASBR 10.4.17.6.
- B. The ASBRs are advertising the redistributed prefixes with a different admin distance and must be changed to 110 on ASBR 10.4.15.5.
- C. The admin distance of the prefixes must be adjusted to 20 on ASBR 10.4.15.5 to advertise prefixes to R1 identically from both ASBRs.
- D. The ASBRs are advertising the redistributed prefixes as Type 1 and must be modified to Type 2
Answer: D
NEW QUESTION # 186
Drag and drop the ICMPv6 neighbor discovery messages from the left onto the correct packet types on the right.
Answer:
Explanation:
NEW QUESTION # 187
......
The Cisco 300-410 exam, also known as Implementing Cisco Enterprise Advanced Routing and Services, is designed for IT professionals who are interested in advancing their knowledge and skills in enterprise networking. This certification exam is part of the CCNP Enterprise track and focuses on advanced routing technologies and services such as BGP, OSPF, and PBR. Passing this exam will demonstrate your ability to configure, troubleshoot, and optimize complex enterprise networks.
Knowledge Required for Passing Cisco 300-410 Exam
To perform well in the Cisco 300-410 exam and obtain one of the associated certifications, the candidates need to possess certain competencies. These include a good grasp of Layer 2 and Layer 3, familiarity with IP services, general understanding of network programmability and automation, as well as basic knowledge of how to manage and secure network devices. It is recommended that the learners also have three to five years of working experience in the networking field.
Authentic 300-410 Dumps With 100% Passing Rate Practice Tests Dumps: https://examschief.vce4plus.com/Cisco/300-410-valid-vce-dumps.html